Sex chat rooms in denver - Dating general question
These vertical seams - finish mold seams vis--vis the upper neck mold seams - may range from just slightly offset to 90 degrees offset (like shown at the linked image above).The offset is a function of the orientation of the parison relative to the two molds (parison and blow molds) used on the particular machine, or occasionally, to the hot parison "sticking" to the neck ring of the parison/blank mold when transferring to the blow mold (Ceramic Industry 19-15).
"Ghost" seams are usually present on the neck, shoulder, and/or body of the bottle if made by a blow-and-blow machine (like the Owens Automatic Bottle Machine).
These are faint, somewhat wandering, hairline seams which if present (usually) are sporadically visible on the sides of machine-made bottles.
Feature #2 (mold seam diameter) is not as strongly diagnostic as the primary indicators as mouth-blown bottles sometimes can have very fine mold seams.
Feature #7 describes a couple glass related features that are quite consistent in machine-made bottles, but not diagnostic, i.e., mouth-blown bottles may sometimes have few/no bubbles in the glass and even thickness.
The machine is operated much as all pressing machines are..." (National Glass Budget 1910; Lockhart pers. This little bottle has a moderately narrow neck and a distinct valve or ejection mark on the base indicating press-and-blow machine manufacture. The 1908 photo below is from the Lewis Hine collection (Library of Congress) and shows an early, probably O'Neill (Barrett 2011) semi-automatic press-and-blow 4 mold milk bottle (which have relatively wide mouths) machine which came with the following caption: "Machine that blows 4 milk bottles at a time. Blowing air would have been supplied by the hose visible at the top of the set of blow molds to the left, where the final "blow" part of the cycle took place.
Added evidence to this theory is that an identical shape and size (2 oz.) "Round Shoe Polish" bottle is shown in the "Machine Made Ware" section of Cumberland's 1911 catalog (Cumberland Glass 1911). Very few narrow neck bottles made on the Owens machines will pre-date that time also. 2007d].) It is thought that probably all pre-1905 semi-automatic bottle machine production in the U. was relegated to wide-mouth bottles/jars due to limitations of the press-and-blow machines at that time (Toulouse 1967; Miller & Sullivan 1981; Jones & Sullivan 1989; Cable 1999; Miller & Mc Nichol 2002; Lockhart pers. This image (click to enlarge) also shows that on many early press-and-blow machines the parison mold was one-piece (note absence of mold hinges) as the narrow non-inflated parison could be removed from either the base or finish mold end (depending on the type machine) whereas the blow mold had to be two-piece (hinges obvious) to remove the expanded and finished bottle if there was any narrowing from the body to the neck/finish (like a typical milk bottle would have).It was noted in 1910 that the Cumberland Glass Company (Bridgeton, NJ) had "...succeeded in perfecting a machine that will satisfactorily produce narrow neck bottles, such as catsups, beer bottles, etc., at a big saving over the hand method." The method used was unusual and may have been unique in bottle-making history: "The machine differs from all others, and in getting the neck upon the bottle, the vessel is made in two sections, the neck being put upon the bowl with a second operation. Manager says machines are fast coming into play in bottle industry, plans eventually to have machines in place of "carrying in boys." Location: Clarksburg, West Virginia" (Library of Congress).This is accomplished so that there is no perceptible mark upon the bottle showing the joint, and the bottle stands every possible test as to strength. Although products of this machine are not conclusively known a bottle such as the one at this link - offset seams shoe polish bottle - may well be a product of the described machine as there is a distinct and abrupt interface edge at the shoulder where the mold seams for both the body and neck end and are offset. This two table semi-automatic machine would have been hand fed with glass (furnace likely to the right) and does have the two different mold sets with the parison molds (where the first "press" part of the cycle took place) the set on the right.Both seams are quite diagnostic of machine manufacture and are usually visible, though the seam at the top of the finish can be hard to see on some bottles - especially if the finish was fire polished.In the glassmaking trade, these seams along with the side mold seams within the finish or just below are referred to as "neck ring" or "neckring" seams since they were formed by the separate neck ring portion of a machine mold (Tooley 1953).This mark is distinctive to the suction process which feeds glass into the bottom of an Owens machine's parison mold.Tags: Adult Dating, affair dating, sex dating